Toshiba Sanitary Electromagnetic Flowmeter TIC-LF494B Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Toshiba Sanitary Electromagnetic Flowmeter TIC-LF494B. Toshiba Sanitary Electromagnetic Flowmeter TIC-LF494B User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
TIC-LF494B
Field Intelligent Device Series
Sanitary Electromagnetic Flowmeter
Introduction
Sanitary electromagnetic flowmeters LF490 series are
designed for applications handling food and beverages.
Sanitary flowmeters must be structured in such a way
that operation and handling is simple, easy and
thorough for the purpose of sanitary control such as
cleaning (CIP/SIP), sterilization and drying. The
sanitary flowmeter has features provided with normal
electromagnetic flowmeters and by using sanitary
fittings for pipeline connections fluid does not remain
in any place along the detector pipeline. Therefore, it is
fit for flowrate measurement for food and beverages.
The electromagnetic flowmeter uses Faraday’s Law of
electromagnetic induction to measure the process flow.
The device consists of two units: a detector, through
which the fluid to be measured flows and in which
low-level signals proportional to flow rates are
obtained; and a converter, which supplies excitation
current to the detector, and amplifies the signals from
the detector and then processes and converts the
signals into the 4–20mAdc current signal or
communication signal. With the unique patented
Mount-Anywhere magnetic field distribution
technology, the meter is highly immune to upstream
flow disturbances. Combined with a multi-functional
converter LF610 (combined type) or LF612 (separate
type) equipped with its patented Noise-Sentry original
noise-suppression circuit and advanced algorithms.
The LF490 has a very high tolerance to noise, giving
the unit a very stable output even for slurry fluid
measurement. IR (Infrared) switches enable parameter
setting of the converter without removing the cover.
Flow direction can be set in either way, and its unique
128 x 128 dot matrix LCD display allows the LCD to
be rotated electronically to 90, 180 and 270 degrees
without opening the cover.
Figure2. LF490 series flowmeters
The AF900 hand-held terminal (HART*
1
communicator) can be used to communicate with the
flowmeter from a remote place. PROFIBUS-PA*
2
interface is available as an option.
*1: HART protocol (Highway Addressable Remote
Transducer) is a communication protocol for industrial
sensors recommended by the HCF
(HART
Communication Foundation).
*2: PROFIBUS is the communication protocol for factory
and process automation that the PROFIBUS
Organization recommends. Instead of analog control
with a conventional analog signal (4-20mA), it is the
fieldbus which digitizes all signals. Flowmeters support
PROFIBUS-PA.
LF494/LF610
LF494/LF612
1S to 4S (25 to 100 mm)
Certification
number
Z01207
Power suppl
y
Converter
I/O
Detector
Power
supply
I/O
Detector
Terminal box
Signal cable
Excitation cable
Converter
LF490/LF610
LF494/LF610F
LF490
LF494
LF612
LF612F
Combined type
LF490/LF610
LF494/LF610F
Separate type
LF490/LF612
LF494/LF612F
Figure1. Configuration
Vue de la page 0
1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1 - Introduction

TIC-LF494B Field Intelligent Device Series Sanitary Electromagnetic Flowmeter Introduction Sanitary electromagnetic flowmeters LF490 series are d

Page 2 - Specifications

TIC-LF494B 10  Wiring Precautions (1) Explosion proof type flowmeters are not provided cable glands. Refer to the part Cable connection port at d

Page 3 - Mag-Prover – Toshiba’s

TIC-LF494B 11 Calibration Range If the calibration range is not specified, the standard range as shown below will be used. If the range is specifi

Page 4

TIC-LF494B 12Table 5. Specification Code (Sanitary type detector LF490 Series) Model Specification Code Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Desc

Page 5 - Installation

TIC-LF494B 13 Table 6. Specification Code for converters Model Specification Code 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Contents LF600 typeLF602 type L

Page 6

TIC-LF494B 14 This Page Intentionally Blank

Page 7 - Long type For English unit

TIC-LF494B 15 This Page Intentionally Blank

Page 8

TIC-LF494B TIC-LF494B Specifications are subject to change without notice.Printed in Japan 2008-5 (TDOC)© TOSHIBA Corporation 2008All Rights Re

Page 9 - Excitation cable

TIC-LF494B 2Specifications  Overall Specifications Measurement range in terms of flow velocity: 0 –1.0 ft/s to 0 – 32.8 ft/s (0 – 0.3 m/s to 0 –10

Page 10 - TIC-LF494B

TIC-LF494B 3 Model LF610 and LF612 converters Input signals Analog signal — the voltage signal from detector, proportional to process flow rate (f

Page 11 - Ordering Information

TIC-LF494B 4• Digital output: OFF • LCD display: No display • PROFIBUS: No communication Power supply: One of the following can be selected: •

Page 12

TIC-LF494B 5Installation  Dimensions (Combined type) Clamp connection Unit : inch(mm) ØD1 L18.86(225) 5.63(143)1.42(36) 5.16(131) (L2) Note1:

Page 13

TIC-LF494B 6Dimensions (Separate type) Clamp connection 3.46(88) 3.58(91) (単位:mm) ΦD1L1 4.96(126) 1.57(40) (L2) R(PT)1/2 Male screw1.38(36) Note1

Page 14

TIC-LF494B 7LF490,LF494DetectorsPipe(welding) Normal type For English unit Meter size (inch) Joint size (ISO2852) L1 (inch) L2 (inch)D1 (inch) D2 (

Page 15

TIC-LF494B 8矢視 A信号ケーブルグランド電源ケーブルグランド封止栓励磁ケーブルグランド電流出力ケーブルグランド接地端子(M4)取付金具4-φ11取付金具82(36) 1561315117820015174 ±0.3矢視A25LCD 表示器赤外線スイッチケーブルグランド(単位:mm)

Page 16

TIC-LF494B 9 Terminal board Connected detector IV wire 5.5 mm2 or more Power switch(External double-pole power switch ) Thick walled steel conduit

Commentaires sur ces manuels

Pas de commentaire