TEC Barcode Printer B-492L/R-TH10 SERIES Owner’s Manual
1. PRODUCT OVERVIEW EO1-33032 1.5 Appearance of the Printer 1- 4 1.5.4 Interior [L Type] [R Type] 1.5.5 Operation Panel
1. PRODUCT OVERVIEW EO1-33032 1.6 Appearance of the Power Supply Unit 1- 5 1.6 Appearance of the Power Supply Unit 1.6.1 Dimensions Dimensions: mm+(
2. PRINTER SETUP EO1-33032 2.1 Precautions 2- 1 2. PRINTER SETUP 2.1 Precautions This section outlines the steps necessary to setup your B-
2. PRINTER SETUP EO1-33032 2.2 Procedure before Operation 2- 2 2.2 Procedure before Operation 2.3 Fitting the Fan Filter This sec
2. PRINTER SETUP EO1-33032 2.4 Connecting the Cables to Your Printer 2- 3 2.4 Connecting the Cables to Your Printer The followin
2. PRINTER SETUP EO1-33032 2.5 Connecting the Power Cord 2- 4 2.5 Connecting the Power Cord 1. Connect the DC power cable
2. PRINTER SETUP EO1-33032 2.6 Turning the Printer ON/OFF 2- 5 2.6 Turning the Printer ON/OFF 2.6.1 Turning ON the Printer 2.6
2. PRINTER SETUP EO1-33032 2.7 Loading the Media 2- 6 2.7 Loading the Media This section describes in detail how to load the media. 1. Op
2. PRINTER SETUP EO1-33032 2.7 Loading the Media 2- 7 2.7 Loading the Media (Cont.) 3. Open the paper entry guide. 4. Loosen the locking screw
2. PRINTER SETUP EO1-33032 2.7 Loading the Media 2- 8 2.7 Loading the Media (Cont.) 7. After loading the media, it may be necessary to set th
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • S
2. PRINTER SETUP EO1-33032 2.7 Loading the Media 2- 9 2.7 Loading the Media (Cont.) 8. There are two issue modes available on this printer.
2. PRINTER SETUP EO1-33032 2.7 Loading the Media 2-10 2.7 Loading the Media (Cont.) (4) Pass the backing paper under the strip plate and above th
2. PRINTER SETUP EO1-33032 2.8 Loading the Ribbon 2-11 2.8 Loading the Ribbon 1. Grasp the tabs on the top and bottom of the
2. PRINTER SETUP EO1-33032 2.9 Inserting the Optional PCMCIA Cards 2-12 2.8 Loading the Ribbon (Cont.) 2.9 Inserting the Optional PCMCIA Car
2. PRINTER SETUP EO1-33032 2.10 Test Print 2-13 2.9 Inserting the Optional PCMCIA Cards (Cont.) 2.10 Test Print 3. The f
3. ON LINE MODE EO1-33032 3.1 Operation Panel 3- 1 3. ON LINE MODE 3.1 Operation Panel This chapter describes usage
3. ON LINE MODE EO1-33032 3.2 Operation 3- 2 3.2 Operation When the printer is turned on, the “ON LINE” message appears on the LC
4. MAINTENANCE EO1-33032 4.1 Cleaning 4- 1 4. MAINTENANCE 4.1 Cleaning 4.1.1 Print Head/Platen This chapter describes
4. MAINTENANCE EO1-33032 4.1 Cleaning 4- 2 4.1.1 Print Head/Platen (Cont.) 4.1.2 Media Guide Plate/ Pinch Roller/Sensors
4. MAINTENANCE EO1-33032 4.1 Cleaning 4- 3 4.1.2 Media Guide Plate/ Pinch Roller/Sensors (Cont.) 3. Remove the lock
Safety Summary EO1-33032 ( ) i 6DIHW\6XPPD U\ Personal safety in handling or maintaining the equipment is extremely important. Warnings and Caut
4. MAINTENANCE EO1-33032 4.1 Cleaning 4- 4 4.1.3 Paper Holder 4.1.4 Covers and Panels 1. Open the paper entry guide. 2.
4. MAINTENANCE EO1-33032 4.2 Care/Handling of the Media and Ribbon 4- 5 4.2 Care/Handling of the Media and Ribbon • Do not store media or ribbon
5. TROUBLESHOOTING EO1-33032 5.1 Error Messages 5- 1 5. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions.
5. TROUBLESHOOTING EO1-33032 5.2 Possible Problems 5- 2 5.1 Error Messages (Cont.) Error Messages Problems/Cause Solutions NO RIBBON **** The ribb
5. TROUBLESHOOTING EO1-33032 5.3 Removing Jammed Media 5- 3 5.3 Removing Jammed Media 5.4 Threshold Setting This section describe
5. TROUBLESHOOTING EO1-33032 5.4 Threshold Setting 5- 4 5.4 Threshold Setting (Cont.) 8. Press and hold the [PAUSE] key until more than 1.5 labels h
6. PRINTER OPERATION EO1-33032 6.1 Overview 6- 1 6. PRINTER OPERATION 6.1 Overview 6.2 Installing the Printer Drivers
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 2 6.2.1 System Requirements 6.2.2 Driver Installation 1. System a.
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 3 6.2.2 Driver Installation (Cont.) 6. Click on the Nex
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 4 6.2.2 Driver Installation (Cont.) If you selected
Safety Summary EO1-33032 ( ) ii If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disc
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 5 6.2.2. Driver Installation (Cont.) 13. Upon clicking on the Next button
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 6 6.2.3 Uninstalling the TEC B-492 Printer Driver
6. PRINTER OPERATION EO1-33032 6.2 Installing the Printer Drivers 6- 7 6.2.3 Uninstalling the TEC B-492 Printer Driver (Cont.) 5. When the foll
APPENDIX 1 SPECIFICATIONS EO1-33032 A1.1 Printer A1- 1 APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use
APPENDIX 1 SPECIFICATIONS EO1-33032 A1.2 Options A1- 2 A1.2 Options Option Name Type Description Source Keyboard module KB-80-QM This module is
APPENDIX 1 SPECIFICATIONS EO1-33032 A1.3 Media A1- 3 A1.3.1 Media Type (Cont.) Unit: mm+(inch) Label dispensing mode Item Batch mode Strip mode W
APPENDIX 1 SPECIFICATIONS EO1-33032 A1.3 Media A1- 4 A1.3.3 Detection Area of the Reflective Sensor The reflective sensor is movable from the center
APPENDIX 1 SPECIFICATIONS EO1-33032 A1.4 Ribbon A1- 5 A1.4 Ribbon Please make sure that the ribbon being used is approved by TOSHIBA TEC. The warra
APPENDIX 2 MESSAGES AND LEDS EO1-33032 APPENDIX 2 MESSAGES AND LEDS A2- 1 APPENDIX 2 MESSAGES AND LEDS Appendix 2 describes the LCD messages display
APPENDIX 2 MESSAGES AND LEDS EO1-33032 APPENDIX 2 MESSAGES AND LEDS A2- 2 NOTES: • If a corrupt command is received, the first 16 bytes of the comma
EO1-33032 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW...
APPENDIX 3 INTERFACE EO1-33032 APPENDIX 3 INTERFACE A3-1 APPENDIX 3 INTERFACE Interface Cables To prevent radiation and reception of electrical
APPENDIX 4 SYSTEM MODE EO1-33032 A4.1 Operation Panel A4- 1 APPENDIX 4 SYSTEM MODE A4.1 Operation Panel Appendix 4 describes usage of th
APPENDIX 4 SYSTEM MODE EO1-33032 A4.2 Overview A4- 2 A4.2 Overview The System Mode consists of nine main menu items: Reset, Self-Diagnostic Test, P
APPENDIX 4 SYSTEM MODE EO1-33032 A4.3 Reset Mode A4- 3 A4.3 Reset Mode A4.4 Self-Diagnostic Test The Reset operation clears all the
APPENDIX 4 SYSTEM MODE EO1-33032 A4.4 Self-Diagnostic Test A4- 4 A4.4 Self-Diagnostic Test (Cont.) While in a Pause condition pre
APPENDIX 4 SYSTEM MODE EO1-33032 A4.4 Self-Diagnostic Test A4- 5 A4.4 Self-Diagnostic Test (Cont.) Print head element che
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4- 6 A4.5 Printer Parameter Fine Adjustment The Printer Parameter
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4- 7 A4.5 Printer Parameter Fine Adjustment (Cont.) While in a Pause cond
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4- 8 A4.5 Printer Parameter Fine Adjustment (Cont.) Strip
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4- 9 A4.5 Printer Parameter Fine Adjustment (Cont.) Back Feed Length Fine
EO1-33032 APPENDIX 1 SPECIFICATIONS ... A1-1 A1.1 Prin
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4-10 A4.5 Printer Parameter Fine Adjustment (Cont.)
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4-11 A4.5 Printer Parameter Fine Adjustment (Cont.)
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4-12 A4.5 Printer Parameter Fine Adjustment (Cont.) Ribbon Motor Vo
APPENDIX 4 SYSTEM MODE EO1-33032 A4.5 Printer Parameter Fine Adjustment A4-13 A4.5 Printer Parameter Fine Adjustment (Cont.) Threshold Manual Fine
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-14 A4.6 Test Print The Test Print menu contains the following: Outline of Test Print In t
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-15 A4.6 Test Print (Cont.) While in a Pause condition press and hold the [RESTART] key until
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-16 A4.6 Test Print (Cont.) Print Speed Setting Select the print speed for the test print.
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-17 A4.6 Test Print (Cont.) Issue Mode Selection Select the issue mode for the test print by se
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-18 A4.6 Test Print (Cont.) Test Print Pattern Selection With “<4>TEST PRINT” displayed
APPENDIX 4 SYSTEM MODE EO1-33032 A4.6 Test Print A4-19 A4.6 Test Print (Cont.) Characters While displaying the Characters, press the
1. PRODUCT OVERVIEW EO1-33032 1.1 Introduction 1- 1 1. PRODUCT OVERVIEW1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Acc
APPENDIX 4 SYSTEM MODE EO1-33032 A4.7 Dump Mode A4-20 A4.6 Test Print (Cont.) A4.7 Dump Mode Auto Print While displaying Auto Print
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-21 A4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and Descrip
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-22 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions (Cont.) (3) Alphanu
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-23 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions (Cont.) Print Head
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-24 A4.8.2 Maintenance Counter and Parameter Check Print Sample and Descriptions •
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-25 A4.8.2 Maintenance Counter and Parameter Check Print Sample and Descriptions (Con
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-26 A4.8.2 Maintenance Counter/Parameter Check Print Sample and Descriptions (Cont.)
APPENDIX 4 SYSTEM MODE EO1-33032 A4.8 Additional Information A4-27 A4.8.2 Maintenance Counter/Parameter Check Print Sample and Descriptions (Cont.)
APPENDIX 5 PRINT SAMPLES EO1-33032 APPENDIX 5 PRINT SAMPLES A5- 1 APPENDIX 5 PRINT SAMPLES Font
APPENDIX 5 PRINT SAMPLES EO1-33032 APPENDIX 5 PRINT SAMPLES A5- 2 APPENDIX 5 PRINT SAMPLES (Cont.) Bar codes 0: JAN8, EAN8 1: MSI 2: Interlea
1. PRODUCT OVERVIEW EO1-33032 1.5 Appearance of the Printer 1- 2 1.5 Appearance of the Printer 1.5.1 Dimensions [L Type]
APPENDIX 5 PRINT SAMPLES EO1-33032 APPENDIX 5 PRINT SAMPLES A5- 3 APPENDIX 5 PRINT SAMPLES (Cont.) K: UPC-A L: UPC-A+2 digits M: UPC-A+5 digits
GLOSSARIES EO1-33032 GLOSSARIES GLOSSARIES Bar code A code which represents alphanumeric characters by using a series of black and white stripes in d
GLOSSARIES EO1-33032 GLOSSARIES Pre-printed label A type of label on which characters, logos, and other designs have been already printed. Printing
INDEX EO1-33032 INDEX INDEX B Backing paper 2-9, A1-3 Bar code A1-1, A4-19, A5-2 Batch mode 2-9 Black mark 2-8, A1-2 Black mark length A1
INDEX EO1-33032 INDEX R Reflective sensor A1-4 Resolution A1-1 RESTART key 1-4, 3-1 Ribbon 2-11, 4-5, A1-5 Ribbon width A1-5 Rotation A
E PRINTED IN JAPAN EO1-33032
1. PRODUCT OVERVIEW EO1-33032 1.5 Appearance of the Printer 1- 3 1.5.2 Front View [L Type] [R Type] 1.5.3 Side View
Commentaires sur ces manuels