Toshiba IK-TF7C Manuel d'utilisateur

For Customer UseEnter below the Serial No.which is located on thebottom of the cabinet. Retainthis information for future ref-erence.Model No.: IK-TF7

102MANU (Manual white balance)• Set the MODE to MANU on the WHT BAL menu.(Refer to the item "7.2 (3) WHT BAL (white balance)".)• Shoot a kno

117. MODE SETTING BY ON SCREEN DISPLAYVarious settings can be controlled on the unit by using the on screen menu displayed on the monitor. Thecontents

127. 2 Menus• Select the menu to change the setting by referring the item "7.1 Using the Menus".)• When the [MENU UP], [MENU DOWN] buttons a

13(1. 2) Changing each setting in SS (synchro. scan) mode(a) Changing the shutter speed setting1Set the "→" to SS by pushing [MENU UP], [MEN

14(1. 3) Changing each setting in E.TRG modeThe E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR.First set the "→" to MODE and select

15(1. 3. 2) Changing each setting in 1P SR mode(a) Changing the polarity of inputting trigger pulse setting1Set the "→" to TRG.P by pushing

16(1. 3. 3) Changing each setting in PW SNR mode(a) Changing the polarity of inputting trigger pulse setting1Set the "→" to TRG.P by pushing

17(1. 3. 4) Changing each setting in PW SR mode-- SHUTTER --MODE E.TRGE.TRG PW SRTRG.PPART OFF<MODE = E.TRG E.TRG = PW SR>• Partial scanning s

18(1. 3. 5) Changing each setting in RR mode(a) Changing the partial scanning setting1Set the "→" to PART by pushing [MENU UP], [MENU DOWN]

19( 3 ) WHT BAL (White balance)WHT BAL has two modes; AWB, MANU.Set the "→" to MODE, push the [DATA UP], [DATA DOWN], and select mode amon

2SAFETY PRECAUTIONSSafety iconsThis manual contains safety instructions that must be observed in order to avoid potentialhazards that could result in

20( 4 ) PROCESS(4. 1) Changing master pedestal1Set the "→" to M. PED by pushing [MENU UP], [MENU DOWN] buttons.2Set the master pedestal by

21( 5 ) SYNCWhen an external sync signal is input, the display menu changes from INT (internal sync) to EXT (externalsync) automatically.(5. 1) Adju

227. 3 External SyncWhen using the unit with an external sync signal, input HD and VD to CC3 and CC4 of the DIGITAL terminal.When the external sync si

23( 3 ) Using the unit with external sync signalWhen adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase

247. 5 EXT TRIG (External trigger)Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images areoutput. T

25About 1 µsExposure period*2Exposure period*2Trigger*1Negative polarity modePositive polarity modeRGB data (video interval image)(Internal VD)*3FVALL

26( 2 ) 1P SR (1 Pulse Trigger Sync Reset)Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync sign

27( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.(3. 1) Pulse Width Trigg

28(3. 2) Pulse Width Trigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync)*1: Externally input signal*2: Exposure time = Trigger pul

29( 4 ) PW SR (Pulse width trigger SYNC-RESET)The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.(4. 1) 1 Pulse Width Trigger

3DisclaimerWe disclaim any responsibility and shall be held harmless for any damages or losses incurred by theuser in any of the following cases:1. Fi

30( 5 ) RR (Reset restart)Input of an external reset-restart signal (CC4 of the DIGITAL terminal: External VD input) permits one screenof informatio

317. 6 Partial Scanning1/29.2s (796H)Video interval imageBlanking intervalBBlanking intervalDTotalAVideo intervalCRGB data (video interval image)(Inte

328. INPUT OUTPUT SIGNAL SPECIFICATOINS2.0 µs to 5.0 µs (Positive polarity mode) (Negative polarity mode)More than 2 µsMore than 2 µs5H to 21H( 6 ) E

339. CCD OUTPUT WAVEFORM TIMING CHART( 1 ) Horizontal Output Waveform Timing Chart246 clk40 clkCLK=33.9 nsec(29.5 MHz)164 clk29 clk3 clk5 clk33.9 nsLV

3410. SPECIFICATIONSPower supplyPower consumptionPick-up systemImage sensor(Effective pixels)Scanning systemScan frequencySync systemHorizontal resolu

3512. BEFORE MAKING A SERVICE CALLSymptomNo imagePoor colorItems to be checked• Is the power supplied correctly?• Is the lens iris adjusted correctly?

LIMITED WARRANTYTOSHIBA CCD CAMERAPromptly register your product with Toshiba on-line at www.toshiba.com/taisisd. By registering your prod-uct you wil

41. CAUTIONS ON USE AND INSTALLATION ... 52. COMPONENTS ... 53. ITEMS CONTROLLED BY USINGON SCREEN DISP

51. CAUTIONS ON USE AND INSTALLATION•Carefully handle the units.Do not drop, or give a strong shock or vibration tothe camera. This may cause problems

63. ITEMS CONTROLLED BY USING ON SCREEN DISPLAYMODEE. TRGMANU speedSyncro.scan.Partial scanningTrigger (1P SNR/SR)Trigger(PW SNR/SR)1Pexposure timeMOD

74. NAMES AND FUNCTIONSDISPPAGEDC IN 12VMENUDATA(AWB)182467593Prism faceplateDIGITAL terminalDISP buttonPAGE button[ Rear ][ Front ]MENU UP buttonMENU

85. CONNECTION5. 1 Standard Connection5. 2 Cautions on Connection• When connecting the camera cables, unplug the power source of the camera and the ot

96. OPERATION1Refer to the item " 5. CONNECTION", connect each equipment correctly.2Turn on the connected equipment and the power source of