Toshiba B-880-QQ SERIES Manuel d'utilisateur

TEC Thermal PrinterB-880-QQ SERIESOwner’s Manual

3. OVERVIEW3.1 FRONT/REAR VIEWFront View Rear View3.2 OPERATION PANELPOWER ON LINE ERRORFEED RESTART PAUSEMESSAGE DISPLAY (LCD)Displays messages in th

Parameter Setting Mode TableFunctionBaud rate of the serial interface is selected.Data length of the serial interface is selected.Stop bit of the se

5-15. SET UP PROCEDUREEO1-330175. SET UP PROCEDURE5.1 REQUIREMENTS FOR OPERATIONThe B-882 has the following requirements:• The host computer must have

Fig. 6-1Fig. 6-26.2 HOLDER STAND INSTALLATIONFit the left and right side holders into the dowels of the holder base and fasten the side holders to the

7-17. LOADING THE RIBBONEO1-330177. LOADING THE RIBBONWARNING!1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing,etc.,

7-27. LOADING THE RIBBONEO1-330175. Push the ribbon core against the spring guide wheel, align the protrusion of the guide wheel with thenotch of the

8-1EO1-330178. LOADING THE MEDIA8. LOADING THE MEDIA3. Lock the Media Holder securely with the Lock Lever.4. Pass the Holder Shaft through the Media,

8-2EO1-330178. LOADING THE MEDIA5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position tothe center. The

8-3EO1-330178. LOADING THE MEDIA7. Set the black mark/feed gap sensor to the correct position by turning the adjusting knob. Turningthe knob right wi

8-4EO1-330178. LOADING THE MEDIA8. The media is now loaded and the sensor position is set.Batch type:MediaFig. 8-6Cutter type: Where a cutter is fitte

Copyright © 2002by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPANThis equipment has been tested and

8-5EO1-330178. LOADING THE MEDIAStrip type:1 Strip labels from the backing paper for about 200-mm long from the top edge of the label roll.2 Lower the

9-19.INSERTING THE OPTIONAL PCMCIA CARD9.INSERTING THE OPTIONAL PCMCIA CARD1. Turn the power off.2. Insert the PCMCIA card into the card slot at the

10-1EO1-3301710.CARE/HANDLING OF THE MEDIA AND RIBBON10.CARE/HANDLING OF THE MEDIA AND RIBBON• Do not store the media and ribbon for longer than the m

11-1EO1-3301711.GENERAL MAINTENANCE11.GENERAL MAINTENANCEWARNING!1. Be cafeful when handling the print head as it becomes very hot.2. Care must be tak

11-2EO1-3301711.GENERAL MAINTENANCE7. Turn the pinch roller lever to the right.8. Remove the white screw and detach the ribbon end sensor plate.NOTE:

11-3EO1-3301711.GENERAL MAINTENANCE11.2UNDER THE MEDIA GUIDES1. Remove the Media Guides.2. Remove the jammed Media.3. Clean “dust and glue” on the Med

11-4EO1-3301711.GENERAL MAINTENANCE11.4REMOVING JAMMED MEDIA1. Turn the power off.2. Open the top cover, and right side cover.3. Turn the head lever

11-5EO1-3301711.GENERAL MAINTENANCE Cleaning the Cutter Unit1. Loosen two screws and remove the cutter cover.2. Remove the white screw and media guid

11-6EO1-3301711.GENERAL MAINTENANCE11.5THRESHOLD SETTINGFor the printer to maintain a constant print position it uses the transmissive sensor to detec

12-1EO1-3301712.TROUBLESHOOTING12.TROUBLESHOOTINGSolution1. Re-fit the media correctly.→ Press the RESTART key.2. Remove the cause of the jam andrep

(i)Safety SummaryEO1-33017Safety SummaryPersonal safety in handling or maintaining the equipment is extremely important. Warnings and Cautionsnecessa

12-2EO1-3301712.TROUBLESHOOTINGSolutionTurn the power off and decrease theprint head temperature.1. Restart the printing by pressingthe RESTART key.

12-3EO1-3301712.TROUBLESHOOTINGSolution1. Check that the media and the ribbon is loaded correctly.2. Check whether the print head is set correctly or

PRINTED IN JAPANEO1-33017

(ii)Safety SummaryEO1-33017CAUTIONThis indicates that there is the risk of personal Injury or damage toobjects if the machines are improperly handled

TABLE OF CONTENTS1. INTRODUCTION ...1- 11.1 APPLICABLE MODEL ...

1-11. INTRODUCTIONEO1-330171. INTRODUCTIONOptional features include a strip mechanism and Cutter mechanism.This manual contains general set-up and mai

2-12. SPECIFICATIONSEO1-33017Supply voltage Universal (automatic switching)85-138 V, 50/60 Hz187-276 V, 50/60 HzBe sure to use a power cord which meet

2-22. SPECIFICATIONSEO1-330172.2 OPTION Auto Ribbon Saving ModeNOTES: 1. To activate ribbon saving function at a speed of 8"/sec., the no print

2.3 MEDIAFig. 2-12. When marking black marks on label rolls, the following requirements must be satisfied.The black mark length should be longer than