Toshiba VF-FS1 Manuel d'utilisateur Page 181
- Page / 252
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E6581381
G-1
7
7. Applied operation
Applied operation can be performed by selecting the frequency mode and command mode setting. However in
case the LOCAL mode is selected by key (lighting a LOC/REM lamp), frequency setting mode and
command mode are fixed operation panel key setting mode. The following explanations are applied REMOTE
mode only.
7.1 Setting the operation frequency
Applied operation can be performed by selecting the inverter frequency setting. To make settings for applied
operation, use the basic parameter HOQF (selection of frequency setting mode 1), and the extended
parameters H (frequency priority selection) and H (selection of frequency setting mode 2).
(1) Operation panel key setting (2) External potentiometer setting
F
R
RES
CC
PLC
PP
VIA
VIB
CC
F
R
RES
CC
PLC
PP
VIA
VIB
CC
VIA
V
SW3
STOPRUNSTOPRUN
HOQF:
H:
Enter the number with the operation panel
keys, then press the key to conform.
(Save the setting)
HOQF:
H:
Use the parameters H to H for this
setting.
LOC
REM
ENT
- Industrial Inverter 1
- I. Safety precautions 3
- ■ General Operation 4
- Danger 4
- ■ Wiring 5
- ■ Operations 6
- Disposal 8
- Attach warning labels 8
- II. Introduction 9
- Contents 10
- 1. Read first 13
- 1.2 Contents of the product 14
- 1.3.1 Outside view 15
- VFFS1-2004 ∼ 2037PM 18
- VFFS1-4004 ∼ 4055PL 18
- ∼ 2185PM 19
- ∼ 4185PL 19
- Warning 21
- 1.3.3 23
- 1.4 Notes on the application 25
- Occurrence of instability 26
- 1.4.2 Inverters 27
- ■ Disposal 29
- Remedies: 30
- 1.4.4 Installation 31
- ■ How to install 33
- Danger 33
- 35
- 2. Connection 37
- 2.2 Standard connections 38
- 2.3 Description of terminals 41
- ■ Power circuit 42
- ■ Control circuit terminals 42
- 3. Operations 47
- Local mode and Remote mode 48
- Sink (Negative) logic 49
- (3) Coast stop 49
- ■ Frequency setting 51
- 3.2 How to operate the VF-FS1 52
- Remote mode selection 53
- 4. Basic VF-FS1 operations 55
- Flow of monitor as following 56
- 4.2 How to set parameters 57
- 5. Basic parameters 67
- HOUN : Meter selection 76
- : Meter adjustment 76
- ■ Resolution 77
- 5.5 Standard default setting 79
- 5.7 Maximum frequency 82
- 5.9 Base frequency 83
- 5.10 Selecting control mode 84
- 2) Setting for fans and pumps 85
- 3) Increasing starting torque 86
- + Motor constant must be set 86
- 5) Energy-saving 87
- , 2 H 91
- 6.1.1 Low-speed signal 97
- : Speed reach detection band 99
- 6.2 Input signal selection 100
- E6581381 101
- ■ Connection method 103
- 1) A-contact input 103
- ■ Input terminal function 107
- 6.4 Basic parameters 2 109
- H, H 117
- H, H 117
- 6.6.1 Starting frequency 118
- 6.7.1 DC braking 119
- 6.10 Bumpless operation 122
- 6.11 PWM carrier frequency 123
- Reduction of rated current 124
- [200V Class for IP20] 124
- Coming soon Coming soon 124
- [400V Class for IP20] 125
- Caution 127
- 6.12.3 Retry function 130
- Output voltage 134
- 6.13 Droop control 135
- 6.14 Conducting PID control 137
- 3) Setting PID control 138
- 6.15 Setting motor constants 141
- (Auto-tuning enabled) 142
- ⇒ See page K-14) 148
- 6.17 Protection functions 150
- : Stall prevention level 2 151
- Caution 151
- 6.17.4 Emergency stop 153
- • Function 154
- ＜Example of operation＞ 156
- 6.17.9 Over-torque trip 157
- H= (Alarm only) 158
- 6.17.12 Undervoltage trip 160
- H : PTC thermal selection 162
- : Inhibitor filter 163
- : Inhibitor gain 163
- 6.19 Adjustment parameters 165
- E.E 167
- : Bias of free unit display 168
- 6.20.4 170
- ■ Example of setting 2 171
- VF-FS1 VF-FS1 VF-FS1 VF-FS1 177
- 6.22 Parameters for options 179
- STOPRUNSTOPRUN 181
- Communic 187
- __KK 188
- 8.2.1 Trip code display 191
- Shielded cable 200
- ■ AIC, Fuse and Wire sizes 202
- 10. Peripheral devices 203
- ■ Selection of wiring devices 204
- Notes on wiring 205
- 11.1 User parameters 209
- 11.2 Basic parameters 209
- 11.3 Extended parameters 212
- • Frequency parameters 213
- • Operation mode parameters 214
- • Torque boost parameters 1 216
- • Input/output parameters 2 216
- • Torque boost parameters 2 216
- • Protection parameters 217
- • Output parameters 219
- • Operation panel parameters 219
- • Communication parameters 220
- • PM motor parameters 222
- 12. Specifications 229
- ■ Common specification 230
- ■ Outside dimensions and mass 232
- ■ Outline drawing 233
- (Continued) 236
- (Continued overleaf) 236
- 14.1 Regular inspection 243
- 14.2 Periodical inspection 244
- (megger) 245
- 15. Warranty 249
- 16. Disposal of the inverter 250
Produits connexes et manuels pour Outils Toshiba VF-FS1
Outils Toshiba E3 Manuel d'utilisateur
(7 pages)
(7 pages)
Outils Toshiba PDP002Z Manuel d'utilisateur
(18 pages)
(18 pages)
Outils Toshiba VF-AS1 Manuel d'utilisateur
(10 pages)
(10 pages)
Outils Toshiba 4200FA Manuel d'utilisateur
(10 pages)
(10 pages)
Outils Toshiba 1000 Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.677 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels