Toshiba VF-FS1 Manuel d'utilisateur Page 5
- Page / 252
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E6581381
3
I
■ Transportation & installation
Danger
See item
Prohibited
• Do not install or operate the inverter if it is damaged or any component is missing.
This can result in electric shock or fire. Please consult your local sales agency for repairs.
Call your local sales agency for repairs.
• Do not place any inflammable objects nearby.
If a flame is emitted due to malfunction, it may result in a fire.
• Do not install in any location where the inverter could come into contact with water or
other fluids.
This can result in electric shock or fire.
1.4.4
1.4.4
2.
Mandatory
• Must be used in the environmental conditions prescribed in the instruction manual.
Use under any other conditions may result in malfunction.
• Mount the inverter on a metal plate.
The rear panel gets very hot. Do not install in an inflammable object, this can result in fire.
• Do not operate with the front panel cover removed. This can result in electric shock.
Failure to do so can lead to risk of electric shock and can result in death or serious injury.
• An emergency stop device must be installed that fits with system specifications (e.g. shut
off input power then engage mechanical brake). Operation cannot be stopped immediately
by the inverter alone, thus risking an accident or injury.
• All options used must be those specified by Toshiba.
The use of any other option may result in an accident.
1.4.4
1.4.4
1.4.4
1.4.4
1.4.4
Warning
See item
Prohibited
• When transporting or carrying, do not hold by the front panel covers.
The covers may come off and the unit will drop out resulting in injury.
• Do not install in any area where the unit would be subject to large amounts of vibration.
That could result in the unit falling, resulting in injury.
2.
1.4.4
Mandatory
• The main unit must be installed on a base that can bear the unit's weight.
If the unit is installed on a base that cannot withstand that weight, the unit may fall
resulting in injury.
• If braking is necessary (to hold motor shaft), install a mechanical brake.
The brake on the inverter will not function as a mechanical hold, and if used for that
purpose, injury may result.
1.4.4
1.4.4
■ Wiring
Danger
See item
Prohibited
• Do not connect input power to the output (motor side) terminals (U/T1,V/T2,W/T3).
That will destroy the inverter and may result in fire.
• Do not connect resistors to the DC terminals (between PA/+ and PC/-).
That may cause a fire.
• Within ten minutes after turning off input power, do not touch wires of devices (MCCB)
connected to the input side of the inverter.
That could result in electric shock.
2.2
2.2
2.2
- Industrial Inverter 1
- I. Safety precautions 3
- ■ General Operation 4
- Danger 4
- ■ Wiring 5
- ■ Operations 6
- Disposal 8
- Attach warning labels 8
- II. Introduction 9
- Contents 10
- 1. Read first 13
- 1.2 Contents of the product 14
- 1.3.1 Outside view 15
- VFFS1-2004 ∼ 2037PM 18
- VFFS1-4004 ∼ 4055PL 18
- ∼ 2185PM 19
- ∼ 4185PL 19
- Warning 21
- 1.3.3 23
- 1.4 Notes on the application 25
- Occurrence of instability 26
- 1.4.2 Inverters 27
- ■ Disposal 29
- Remedies: 30
- 1.4.4 Installation 31
- ■ How to install 33
- Danger 33
- 35
- 2. Connection 37
- 2.2 Standard connections 38
- 2.3 Description of terminals 41
- ■ Power circuit 42
- ■ Control circuit terminals 42
- 3. Operations 47
- Local mode and Remote mode 48
- Sink (Negative) logic 49
- (3) Coast stop 49
- ■ Frequency setting 51
- 3.2 How to operate the VF-FS1 52
- Remote mode selection 53
- 4. Basic VF-FS1 operations 55
- Flow of monitor as following 56
- 4.2 How to set parameters 57
- 5. Basic parameters 67
- HOUN : Meter selection 76
- : Meter adjustment 76
- ■ Resolution 77
- 5.5 Standard default setting 79
- 5.7 Maximum frequency 82
- 5.9 Base frequency 83
- 5.10 Selecting control mode 84
- 2) Setting for fans and pumps 85
- 3) Increasing starting torque 86
- + Motor constant must be set 86
- 5) Energy-saving 87
- , 2 H 91
- 6.1.1 Low-speed signal 97
- : Speed reach detection band 99
- 6.2 Input signal selection 100
- E6581381 101
- ■ Connection method 103
- 1) A-contact input 103
- ■ Input terminal function 107
- 6.4 Basic parameters 2 109
- H, H 117
- H, H 117
- 6.6.1 Starting frequency 118
- 6.7.1 DC braking 119
- 6.10 Bumpless operation 122
- 6.11 PWM carrier frequency 123
- Reduction of rated current 124
- [200V Class for IP20] 124
- Coming soon Coming soon 124
- [400V Class for IP20] 125
- Caution 127
- 6.12.3 Retry function 130
- Output voltage 134
- 6.13 Droop control 135
- 6.14 Conducting PID control 137
- 3) Setting PID control 138
- 6.15 Setting motor constants 141
- (Auto-tuning enabled) 142
- ⇒ See page K-14) 148
- 6.17 Protection functions 150
- : Stall prevention level 2 151
- Caution 151
- 6.17.4 Emergency stop 153
- • Function 154
- ＜Example of operation＞ 156
- 6.17.9 Over-torque trip 157
- H= (Alarm only) 158
- 6.17.12 Undervoltage trip 160
- H : PTC thermal selection 162
- : Inhibitor filter 163
- : Inhibitor gain 163
- 6.19 Adjustment parameters 165
- E.E 167
- : Bias of free unit display 168
- 6.20.4 170
- ■ Example of setting 2 171
- VF-FS1 VF-FS1 VF-FS1 VF-FS1 177
- 6.22 Parameters for options 179
- STOPRUNSTOPRUN 181
- Communic 187
- __KK 188
- 8.2.1 Trip code display 191
- Shielded cable 200
- ■ AIC, Fuse and Wire sizes 202
- 10. Peripheral devices 203
- ■ Selection of wiring devices 204
- Notes on wiring 205
- 11.1 User parameters 209
- 11.2 Basic parameters 209
- 11.3 Extended parameters 212
- • Frequency parameters 213
- • Operation mode parameters 214
- • Torque boost parameters 1 216
- • Input/output parameters 2 216
- • Torque boost parameters 2 216
- • Protection parameters 217
- • Output parameters 219
- • Operation panel parameters 219
- • Communication parameters 220
- • PM motor parameters 222
- 12. Specifications 229
- ■ Common specification 230
- ■ Outside dimensions and mass 232
- ■ Outline drawing 233
- (Continued) 236
- (Continued overleaf) 236
- 14.1 Regular inspection 243
- 14.2 Periodical inspection 244
- (megger) 245
- 15. Warranty 249
- 16. Disposal of the inverter 250
Produits connexes et manuels pour Outils Toshiba VF-FS1
Outils Toshiba E3 Manuel d'utilisateur
(7 pages)
(7 pages)
Outils Toshiba PDP002Z Manuel d'utilisateur
(18 pages)
(18 pages)
Outils Toshiba VF-AS1 Manuel d'utilisateur
(10 pages)
(10 pages)
Outils Toshiba 4200FA Manuel d'utilisateur
(10 pages)
(10 pages)
Outils Toshiba 1000 Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.799 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels