Toshiba E-STUDIO900 Manuel d'utilisateur Page 202
- Page / 224
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PTM 7-27 B070/B071
7.8.2 JOGGER UNIT DRIVE
At prescribed intervals, the jogger motor [A] switches on and drives the jogger
timing belt [B], gear [C] and jogger fence timing belt [D] which drives the shift
jogger fences [E] against the sides of the stack to align its edges.
At the end of the job, the jogger fence lift motor [F] switches on and raises the
fences until the actuator [G] leaves the slot of the shift jogger fence lift HP sensor
[H] and shuts off the shift jogger fence lift motor.
At the same time, the jogger motor reverses and drives the fences away from the
sides of the stack until the actuator [I] deactivates the shift jogger fence HP sensor
[J] and switches off the jogger motor.
The jogger fences remain up in the standby position until the next job starts.
B513D002.WMF
[F]
[G]
[H]
[A]
[B]
[C]
[D]
[E]
[I]
[J]
- TECHNICAL TRAINING 1
- PROGRAM 1
- INTRODUCTION 5
- CONTENTS 8
- IMPORTANT SAFETY NOTICES 9
- WARNING 10
- CONVENTIONS IN THIS MANUAL 11
- 1.1 SPECIFICATIONS 14
- B070/B071 1-2 PTM 15
- PTM 1-3 B070/B071 16
- 1.1.2 ADF 17
- 1.2 MACHINE CONFIGURATION 18
- 1.3 COMPONENT LAYOUT 19
- 1.3.2 ADF 20
- 1.4 PAPER PATH 21
- 1.5 COPY PROCESS 22
- B070/B071 1-10 PTM 23
- PTM 2-1 B070/B071 26
- 2.1 DOCUMENT FEEDER 26
- PTM 2-2 B070/B071 27
- 2.1.2 BOTTOM PLATE LIFT 27
- PTM 2-3 B070/B071 28
- 2.1.3 PICK-UP AND SEPARATION 28
- PTM 2-4 B070/B071 29
- 2.1.4 ORIGINAL FEED 29
- PTM 2-5 B070/B071 30
- PTM 2-6 B070/B071 31
- 2.1.6 ORIGINAL TRANSPORT 31
- PTM 2-7 B070/B071 32
- PTM 2-8 B070/B071 33
- PTM 2-9 B070/B071 34
- PTM 2-10 B070/B071 35
- PTM 2-11 B070/B071 36
- PTM 2-12 B070/B071 37
- 2.2 SCANNING 37
- 2.2.1 OVERVIEW 37
- PTM 2-13 B070/B071 38
- 2.2.2 SCANNER DRIVE 38
- PTM 2-14 B070/B071 39
- PTM 2-15 B070/B071 40
- PTM 2-16 B070/B071 41
- 2.3 IMAGE PROCESSING 41
- PTM 2-17 B070/B071 42
- 2.3.3 IMAGE PROCESSING FLOW 43
- PTM 2-19 B070/B071 44
- PTM 2-20 B070/B071 45
- 2.3.4 IMAGE PROCESSING MODES 45
- Mode Setting Function 45
- PTM 2-21 B070/B071 46
- PTM 2-22 B070/B071 47
- Item Range Default SP No 47
- PTM 2-23 B070/B071 48
- PTM 2-24 B070/B071 49
- PTM 2-25 B070/B071 50
- PTM 2-26 B070/B071 51
- PTM 2-27 B070/B071 52
- PTM 2-28 B070/B071 53
- PTM 2-29 B070/B071 54
- PTM 2-30 B070/B071 55
- 2.4 LASER EXPOSURE 55
- 2.4.1 OVERVIEW 55
- PTM 2-31 B070/B071 56
- PTM 2-32 B070/B071 57
- 2.4.3 LD SAFETY SWITCHES 57
- PTM 2-33 B070/B071 58
- PTM 2-34 B070/B071 59
- 2.4.5 POLYGON MIRROR MOTOR 59
- PTM 2-35 B070/B071 60
- 2.4.6 1200-DPI RESOLUTION 60
- Main Scan 60
- Sub Scan 60
- PTM 2-36 B070/B071 61
- 2.4.7 OPTICAL PATH 61
- PTM 2-37 B070/B071 62
- 2.5 DRUM UNIT 62
- 2.5.1 PROCESS CONTROL 62
- PTM 2-38 B070/B071 63
- 2.5.2 DRUM UNIT COMPONENTS 63
- PTM 2-39 B070/B071 64
- 2.5.3 DRUM DRIVE 64
- PTM 2-40 B070/B071 65
- 2.5.4 DRUM CHARGE 65
- PTM 2-41 B070/B071 66
- PTM 2-42 B070/B071 67
- 2.5.5 DRUM CLEANING 67
- PTM 2-43 B070/B071 68
- 2.5.6 CLEANING UNIT DRIVE 68
- PTM 2-44 B070/B071 69
- PTM 2-45 B070/B071 70
- 2.5.7 OTHERS 70
- PTM 2-46 B070/B071 71
- PTM 2-47 B070/B071 72
- PTM 2-48 B070/B071 73
- 2.6 DEVELOPMENT 73
- 2.6.1 OVERVIEW 73
- PTM 2-49 B070/B071 74
- 2.6.2 DEVELOPMENT MECHANISM 74
- PTM 2-50 B070/B071 75
- 2.6.3 DRIVE 75
- PTM 2-51 B070/B071 76
- 2.6.4 CROSSMIXING 76
- PTM 2-52 B070/B071 77
- 2.6.5 DEVELOPMENT BIAS 77
- PTM 2-53 B070/B071 78
- 2.7.1 OVERVIEW 78
- PTM 2-54 B070/B071 79
- 2.7.2 TONER BANK 79
- PTM 2-55 B070/B071 80
- PTM 2-56 B070/B071 81
- PTM 2-57 B070/B071 82
- PTM 2-58 B070/B071 83
- PTM 2-59 B070/B071 84
- PTM 2-60 B070/B071 85
- 2.7.4 TONER HOPPER 85
- PTM 2-61 B070/B071 86
- PTM 2-62 B070/B071 87
- PTM 2-63 B070/B071 88
- PTM 2-64 B070/B071 89
- 2.8 PAPER FEED 89
- 2.8.1 OVERVIEW 89
- PTM 2-65 B070/B071 90
- 2.8.2 DRIVE 90
- PTM 2-66 B070/B071 91
- 2.8.3 VERTICAL TRANSPORT 91
- PTM 2-67 B070/B071 92
- 2.8.4 PAPER REGISTRATION 92
- From the LCT 92
- PTM 2-68 B070/B071 93
- 2.9.1 OVERVIEW 93
- PTM 2-69 B070/B071 94
- PTM 2-70 B070/B071 95
- PTM 2-71 B070/B071 96
- 2.9.4 TONER COLLECTION 96
- PTM 2-72 B070/B071 97
- PTM 2-73 B070/B071 98
- 2.10 FUSING 98
- 2.10.1 OVERVIEW 98
- PTM 2-74 B070/B071 99
- PTM 2-75 B070/B071 100
- PTM 2-76 B070/B071 101
- Area Near-End Web Remaining 101
- PTM 2-77 B070/B071 102
- 2.11 PAPER EXIT/DUPLEX 102
- 2.11.1 OVERVIEW 102
- PTM 2-78 B070/B071 103
- 2.11.2 INVERTER 103
- PTM 2-79 B070/B071 104
- PTM 2-80 B070/B071 105
- PTM 2-81 B070/B071 106
- PTM 2-82 B070/B071 107
- PTM 2-83 B070/B071 108
- PTM 2-84 B070/B071 109
- PTM 2-85 B070/B071 110
- 2.12.1 OVERVIEW 110
- 2.12.2 ENERGY SAVER MODE 111
- 2.12.3 LOW POWER MODE 112
- 2.12.4 AUTO OFF MODE 113
- 2.12.5 NIGHT MODE 114
- 3. SERVICE TABLES 117
- Using the SP Mode 118
- Direct Entry 118
- Button Selection Entry 118
- SP Mode Button Summary 119
- SP1-nnn Feed 120
- 3.3 USER PROGRAM MODE 121
- 4. INSTALLATION 125
- 4.1.2 MACHINE LEVEL 126
- B070I410.WMF 127
- B070I023.WMF 127
- 4.1.4 DIMENSIONS 128
- CAUTION 129
- 4.2 COPIER (B070/B071) 130
- PTM 4-7 B070/B071 131
- 1/2"x11" LEF, A5 134
- 1/2"x81/2" 134
- B070/B071 5-2 PTM 135
- PTM 5-3 B070/B071 136
- B070/B071 5-4 PTM 137
- 5.4 DRIVE LAYOUT 138
- 5.5 DETAILED DESCRIPTIONS 139
- 5.5.2 PICK-UP AND FEED 140
- 5.5.3 PICK-UP AND FEED 141
- PTM 5-9 B070/B071 142
- 5.6 PAPER LIFT 143
- 5.6.3 LIFT SENSOR 144
- 5.7 PAPER SIZE DETECTION 145
- PTM 5-13 B070/B071 146
- 5.9 PAPER END DETECTION 147
- Upper Tray 150
- Lower Tray 150
- Proof Tray 150
- Staple Specifications 151
- 6.2 PUNCH UNIT (B377) 152
- B070/B071 6-4 PTM 153
- 6.4 DRIVE LAYOUT 154
- B070/B071 6-6 PTM 155
- 6.5 DETAILED DESCRIPTIONS 156
- 6.5.2 PRE-STACKING 157
- Overview 158
- 6.5.4 UPPER TRAY 159
- 6.5.5 LOWER TRAY 160
- Lower Tray Full 161
- 6.5.6 SHIFT MECHANISM 162
- 6.5.7 PAPER POSITIONING 163
- 6.5.8 STAPLER 164
- 6.5.9 STAPLER MOVEMENT 165
- Rotational Stapler Movement 166
- 6.5.10 FEED OUT 167
- 6.5.11 BOOKLET FINISHING 168
- 6.5.13 INITIAL FOLDING 169
- PTM 6-21 B070/B071 170
- 6.6.1 PUNCH DRIVE MECHANISM 171
- PTM 6-23 B070/B071 172
- 6.6.2 PUNCH WASTE COLLECTION 173
- 7.1 SPECIFICATION 176
- 1/2" x 81/2" SEF 177
- 1/2" x11" LEF 177
- 1/2" x 11" LEF 177
- 1/2" x 11" SEF 178
- PTM 7-5 B070/B071 180
- Symbol Name Function 181
- SENSORS 181
- B070/B071 7-8 PTM 183
- 7.4 DRIVE LAYOUT 184
- 7.5 DETAILED DESCRIPTIONS 185
- 7.5.2 PAPER PRE-STACKING 186
- B070/B071 7-12 PTM 187
- 7.5.4 STAPLER UNIT MOVEMENT 188
- Rotation (1) 189
- Rotation (2) 189
- 7.5.5 STAPLER 190
- B070/B071 7-16 PTM 191
- 7.5.6 FEED-OUT 192
- 7.5.7 PAPER EXIT STACKING 193
- 7.5.8 SHIFT TRAY 194
- Sort/Stack Mode (Shift Mode) 195
- Staple Mode 195
- PTM 7-21 B070/B071 196
- B070/B071 7-22 PTM 197
- 7.6 JAM CONDITIONS 198
- 7.7.1 PUNCH UNIT DRIVE 199
- 7.7.2 PUNCH WASTE COLLECTION 200
- B070/B071 7-26 PTM 201
- 7.8.2 JOGGER UNIT DRIVE 202
- 1/2" x 81/2" 205
- 8.2.1 MAIN LAYOUT 206
- 8.2.2 DRIVE LAYOUT 207
- 8.3 DETAILED DESCRIPTIONS 208
- 8.3.2 PAPER FEED 209
- 8.3.3 PAPER SIZE DETECTION 210
- : Cannot be corrected 211
- B070/B071 8-8 PTM 212
- 9.1 SPECIFICATION 215
- B070/B071 9-2 PTM 216
- PTM 9-3 B070/B071 217
- B070/B071 9-4 PTM 218
- 9.4 DRIVE LAYOUT 219
- 9.5 DETAILED DESCRIPTIONS 220
- 9.5.2 PAPER FEED 221
- 9.5.3 PAPER SIZE DETECTION 222
- B070/B071 9-10 PTM 224
© 2020, manymanuals.fr. Tous droits réservés | 1.346 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels